- How To Use
The Pryme mini cleaning wheel kit is your go to for cleaning in tight areas where bigger wheels can't get to. This kit is available for either a dremel tool (1/8" shaft) or die grinder tool (1/4" shaft).
Includes tool adapter, 3 fine grade wheels, and 3 coarse grade wheels. Wheels come in sizes from 1" to 2" in diameter.
- Use the coarse wheels for scratch removal and aggressive sanding, use the fine wheels for a smooth, brushed type finish
- Works great for paint preparation too
- Best for aluminum, but can be used on steel, stainless steel, and brass with great results (steel and brass must be coated afterwards to prevent rust and corrosion).
- Tool adapter is machined from stainless steel and includes a low profile stainless mounting screw
- Proudly made in the USA
Fine Wheel Specs:
Bring your old parts back from the dead with a Pryme fine cleaning wheel. Cleans, brightens, and leaves behind a brushed type finish.
- Comparable to 400 grit sandpaper
- 3/8" thick
- Max RPM: 25,000
Coarse Wheel Specs:
For those of you looking to smooth out scratches, scrapes, or casting lines, the Pryme coarse grade wheel is the ticket! Also works great for removal of rust, corrosion, and paint.
- Comparable to 180 grit sandpaper
- Max RPM: 25,000
Click on "Video" tab to see the kit in use.
-Dremel not included.
-Always wear a dust mask or respirator and proper eye protection while buffing!
Tags: Cleaning, Pad, Wheel, Scuff, Scotch, Abrasive, Sanding, Drum, Dremel Attachment, Buff, Buffing, Die Grinder Attachment, Wheel Adapter, Adapter, Mandrel, Shank, Template, Kit, Mini, Pack
The Dremel kit is designed to be used on a Dremel or rotary tool that uses a 1/8" shaft size.
The Dremel tool I recommend Click Here
Some cheaper alternatives:
Avid Rotary Tool Click Here
Tacklife Rotary Tool Click Here
The die grinder kit is designed to be used on an air die grinder or rotary tool that uses a 1/4" shaft size. Could be used on a drill as well. The best results will come with it on a die grinder.
My recommended die grinder Click Here
Some cheaper alternatives:
Ingersoll Rand Grinder Click Here
Neiko Grinder Click Here
If you don't have an air compressor, here is a good electric die grinder Click Here
Whenever you're doing any sort of grinding or sanding you'll want to use eye and respiratory protection. Trust me, you do not want to be breathing in metal particles!
A great product for protecting yourself is this respirator Click Here
Alternatively, this is also a great respirator to pair up with safety glasses Click Here
Use these filters with the previously mentioned respirators Click Here
If you're doing lots of buffing, I'd recommend getting some sort of ventilation like this exhaust fan that I use Click Here
And of course, always a good idea to wear gloves Click Here
- Install wheel onto adapter shaft and snug down mounting screw.
- Slide adapter shaft at least 3/4" into the tool, securely fasten, and get cleaning!
- Use the rough wheels for scratch removal and aggressive sanding, use the fine wheels for a smooth, brushed type finish
- Remove as much grease, oil, and dirt as you can before using the wheels, so you’re not contaminating them.
- Sand or buff in the same direction if you’re going for a brushed look. Intersecting scratches do not look good.
- Try to buff evenly across the part so you don't end up with dips or low spots.
- Use light pressure with the wheel or you'll wear it out prematurely. If you need to apply heavy pressure, you should go to a more aggressive wheel. Refer to buffing chart below.
- In order to make the wheels last as long as possible, stay away from sharp edges. The direction of the wheel should be spinning away from an edge and not towards it.
- Refer to the buffing chart below for the proper wheels to use with each metal type, as well as the steps to achieve the desired finish.
- If you have problems achieving a good finish, refer to the troubleshooting guide below.
- Always wear a dust mask or respirator and eye protection while buffing!
- A clear ceramic coating will protect your part after buffing.
- Steel and magnesium parts must be protected with a coating, bare steel will rust quickly and magnesium corrodes in a matter of hours. Stainless steel and aluminum can be left bare without corrosion issues, as long as you keep the parts clean and out of the weather during storage.
- To achieve a consistent brushed look on larger parts, finish it by hand with a hand pad, going in the same direction you were buffing in.
They sent me extras and they work so well thank u cam and prime mx
Thanks for your feedback Alex! It's great to hear the wheels are working well for you. Your business is greatly appreciated!
Super High quality at a Bargain of a price. Dremel brand cleaning wheels fall apart in minutes of use and are $20 for two wheels… I was able to polish all my my linkage components in minutes. Little to no wear on the coarse and fine wheels I used when finished. High density. Leaves an amazing finish. Chuck bit supplied with kit is of great quality as well. Will definitely be ordering more wheels from Pryme in the very near future! Highly recommend. Shipping was very fast as well (Even to Alaska!)
Thanks for the excellent review Robert, your feedback is greatly appreciated! Happy to see the wheels made a difference for you. Your support of Pryme is greatly valued!
nice variety of sizes of wheels and easy to use and get all the parts nice and shiny!
Happy to hear you're achieving good results with the wheels! Thanks for your review Nick, your support of Pryme is greatly appreciated!
great product and easy to use, was able to get my engine case and metal parts on my ktm nice and polished! definitely recommend and would buy again
Great store and great parts to clean up your dirt bike or anything metal…