- How To
These will be available on 5/27/23. Click "Email Me When Available" after you've selected your model to receive an email update when these go up for sale.
What Do They Do?
- Protects the coating or metal on your ignition/flywheel cover
- Covers up a worn looking cover
- Gives your bike a clean look
What Are They?
These are thick vinyl protectors that have a very strong adhesive backing. They apply easily but don't add bulk to your engine cover.
Available in one guard, or sets of 3 and 5 to save you cash!
Keep in mind, these guards do not last forever. The lifetime of them depends on the care taken while installing, as well as your riding style. Protecting your engine covers with guards is much cheaper and easier than refinishing your covers every few months due to wear and tear on the coatings/metal.
Image may not be an exact representation of the guard for your model, but you will receive the correct guard for your bike.
- For protecting your frames, see our Frame Guards
- Guards are also available in packs with Clutch Guards and Frame Guards.
- Made from 0.5mm thick vinyl
- Extreme high adhesion allows guard to stay in place
- Perfect fit ensures edges do not peel up prematurely
- All black design with model of bike and Pryme logo printed into guard
- Features a corner guard, which prevents peeling in high wear areas
- Adheres to aluminum, steel, plastic, powder coat, and cerakote
- Sold individually, or in sets of 3 and 5 to save you cash!
- 100% made in the USA!
Some guards may have a cutout around raised lettering, such as on CR125 models. These only fit on stock ignition covers.
- Have a heat gun or hair dryer on hand.
- Do not use any type of water, windex, or soap solution while installing guards.
- Install guards in a warm area to help them adhere and conform better.
- Remove any glue, dirt, or grease from frame or cover.
- Clean surface with isopropyl alcohol or contact cleaner, and let dry.
- Use a heat gun or hair dryer to warm up the surface and guard if temperature is below 60F.
- Peel part of the paper backing away, and line up guard at the most detailed part.
- Be sure not to touch the part surface or adhesive with your bare hands.
- Once you are happy with the alignment, tack the guard down at the center and work your way from the center towards the edges.
- If the guard is off center or an air bubble starts to form, you can carefully peel up the guard to correct.
- As you get to the edges and tighter spots, creases may start to form. Add a small amount of heat to stretch the guard so it lays flat.
- Do not apply excessive heat, as this may melt the guard.
- If your cover or frame has tight crevices, use a soft rubber or plastic edge to help press the guard into those spots.
- Once the guard is fully tacked in place, heat the guard again while applying pressure. This is very important to the adhesion of the guard, so make sure you don't skip this step.
Getting The Most Out Of Your Guards
- When installing the guard, make 100% sure the surface is clean and the edges are not hanging off the part.
- It is not recommended to use boots with steel toe caps, as this will wear out guards much quicker.
- If you notice an edge start to peel up, apply heat and tack it back down or lightly trim the edge.
- If using a pressure washer to clean your bike, take caution around the guards.
Removing Old Guards
- Before removing a worn guard, apply heat to help soften up the adhesive, this will also prevent adhesive from being left behind.
- If adhesive is left afterwards, tack the old guard over the adhesive and this will help peel it up. Use a contact cleaner or isopropyl alcohol to remove any leftover adhesive.
Tags: Grip Tape, Frame Tape, Engine Tape, Clutch Cover Guard, Flywheel Cover Guard, Ignition Cover Guard, Engine Cover, Frame Grip, Engine Grip, Frame Covers, Engine Guard
Tracking Information Tracking numbers will be uploaded to the order page and sent to your email inbox. It may take up to 24 hours for the tracking page to show the most recent information.
We are not to be held responsible for stolen or lost packages, packages sent to the wrong address, or refunding/replacing packages in these scenarios. It is the customer's responsibility to file all shipping claims.
Returns We accept returns within 14 days after your item has been delivered. If 14 days have gone by since your item was delivered, unfortunately we cannot offer you a refund. To initiate a return please send us an email at firstname.lastname@example.org. To be eligible for a return, your item must be in the same condition that you received it. The item must be unused / unworn and original tags attached. No returns allowed on sale/clearance items.
Refunds Once your return is received and inspected, we will send you an email to notify you that we have received your returned item. Your refund will be processed and a credit will automatically be applied to your credit card or original method of payment, within 7 days.
Late or Missing Refunds If you haven’t received a refund for your return yet, first check your bank account. Then contact your credit card company, it may take some time before your refund is officially posted. If you’ve done all of this and you still have not received your refund yet, please contact us at email@example.com.
Shipping Costs You will be responsible for paying the return shipping costs of your item. Additionally, the original shipping costs will not be refunded.
Exchanges If you need to exchange an item, please see our refund policy above and include exchange instructions with the return. We do not offer exchanges on out of stock items. If the item is out of stock then we will refund you instead. The buyer is responsible for all shipping costs on exchanges.
Incorrect or Defected Item If we made a mistake with your order, please contact us at firstname.lastname@example.org. We will provide a return label if an exchange needs to be made. You must notify us within 14 days of delivery of any defects with the item. Any claims past 14 days will be considered wear and tear, and cannot be replaced.