Pryme Cleaning Wheel Starter Pack
Pryme Cleaning Wheel Starter Pack
Pryme Cleaning Wheel Starter Pack
Pryme Cleaning Wheel Starter Pack
Pryme Cleaning Wheel Starter Pack

Cleaning Wheel Starter Pack

Regular price $40.00 Save $-40.00

Only 9999994 items in stock!

Grab everything you need to get started in parts restoration with one click! The Pryme cleaning wheel starter pack will get your bench grinder or buffing machine ready to go for some serious cleaning and polishing. This pack will save you some cash over buying everything separately too!

This pack includes (1) fine grade wheel, (1) rough grade wheel, 4 flanges, and 2 spacers. The wheels are available in 6" and 8" diameter. Flanges and spacers are available for machines with a 1/2", 5/8", or 3/4" shaft.

  • Mounts on a bench grinder / buffing machine.
  • Use the rough wheel for scratch removal and aggressive sanding, use the fine wheel for a smooth, brushed type finish.
  • Works great for paint preparation too.
  • Best for aluminum, but can be used on steel, stainless steel, and brass with great results.
  • For best results, use on 1/2 HP+ buffer or bench grinder. Can be used on a high speed drill with decent results too.
  • Proudly made in the USA.
  • The larger the wheel, the longer it will last. The smaller wheels work better in tighter areas however and also cost a bit less.

Fine Wheel Specs:

Bring your old parts back from the dead with a Pryme fine cleaning wheel. Cleans, brightens, and leaves behind a brushed type finish.

  • Comparable to 320 grit sandpaper
  • 3/8" thick x 1/2" center hole (can be used on 1/2", 5/8", and 3/4" buffer shaft sizes)
  • Max RPM: 3600

Rough Wheel Specs:

For those of you looking to smooth out scratches, scrapes, or casting lines, the Pryme rough grade wheel is the ticket! Also works great for removal of rust, corrosion, and paint.

  • Comparable to 180 grit sandpaper
  • 3/8" thick x 1/2" center hole (can be used on 1/2", 5/8", and 3/4" buffer shaft sizes)
  • Max RPM: 3600

Flange Specs:

The Pryme wheel flange set ensures your buffing wheel stays in place on the machine while buffing. Installing a flange on either side of your wheel clamps the wheel securely to the shaft. These flanges also have a built in step that pushes the wheel towards the end of the machine's shaft, creating more space between the wheel and the machine. 

The premium flange set features drilled holes to provide a better grip on the wheel and help keep the wheel cool.

  • 2" diameter
  • 1/3" wide
  • Made from CNC machined aluminum for a trick look and great durability

Spacer Specs:

Open up more space for your buffing activities with a Pryme wheel spacer. This spacer pushes the wheel towards the end of the buffing machine's shaft, creating more space between the wheel and the machine. 

  • 1/2" width
  • CNC machined from aluminum for a precise fit with excellent durability

Click on "Video" tab to see the wheels in use.

-Buffer motor or stand not included
-Always wear a dust mask or respirator and proper eye protection while buffing!

Related Items:
Click here to purchase the wheels without the spacers and flanges.
The flanges and spacers are available separately on this page.

Check out the videos below of the wheels working their magic. 

Tags: Cleaning, Pad, Wheel, Scuff, Scotch, Abrasive, Buff, Buffing, Scotch Brite Wheel, Scotch Brite Pad, Abrasive Wheel, Abrasive Pad, Buffing Wheel, Buffing Pad

These wheels are designed to be used on a buffing machine or bench grinder. They can be used on a machine with a 1/2", 5/8", or 3/4" shaft. For a buffing machine, you'll want at least a 1/2 HP motor that spins at 3000 RPM. One with an extended shaft is best, so you have lots of clearance to buff your parts.

If you'll be doing lots of buffing, opt for a 3/4 HP motor. Also, a 2 speed (typically 1800/3600 RPM) machine offers more versatility and is a great option.

Personally, this is the machine I use (Baldor motor, will last a lifetime) Click Here

Some great alternatives:

Eastwood Single Speed Click Here

Eastwood Dual Speed Click Here

Great Economy Buffer Click Here

If you have an existing machine but need the big washers that hold the wheels in place Click Here

To space the wheels away from the machine for more clearance Click Here

To extend the shaft on your buffer Click Here

To use the wheels on a drill Click Here

Whenever you're doing any sort of grinding or sanding you'll want to use eye and respiratory protection. Trust me, you do not want to be breathing in metal particles! At the bare minimum, wear a dust mask and glasses.

A great product for protecting yourself is this respirator Click Here

Alternatively, this is also a great respirator to pair up with safety glasses Click Here

Use these filters with the previously mentioned respirators Click Here

If you're doing lots of buffing, I'd recommend getting some sort of ventilation like this exhaust fan that I use Click Here

And of course, always a good idea to wear gloves Click Here


  • Secure wheel to buffer shaft with a flange on either side. On some wheels, you may have to spin the wheel to help it onto the shaft on the larger 5/8" and 3/4" shaft sizes.
  • Tighten down the nut until the wheel is secure on the shaft and doesn’t spin (use a spacer if your nut bottoms out on the threads).


  • Remove as much grease, oil, and dirt as you can before using the wheels, so you’re not contaminating them.
  • Sand or buff in the same direction if you’re going for a brushed look. Intersecting scratches do not look good.
  • Don’t spend too much time in one area, or you’ll end up with a dip or low spot. Try to buff evenly across the part.
  • Use light pressure with the wheel or you'll wear it out prematurely. If you need to apply heavy pressure, you should go to a more aggressive wheel.
  • Buffing against the direction the wheel is spinning will cut quicker, buffing with the spinning of the wheel will give a smoother finish.
  • In order to make the wheels last as long as possible, stay away from sharp edges. The direction of the wheel should be spinning away from an edge and not towards it. Adjust the orientation of the part accordingly. 
  • The sweet spot to buff on the wheel is between 4 and 5 o’clock. Look at your buffing machine from the left side, and picture where 4 and 5 o’clock are on the wheels. That is where you will want the part to touch the wheel when buffing.
  • A clear ceramic coating will protect your part after buffing.
  • Steel and magnesium parts must be protected with a coating, bare steel will rust quickly and magnesium corrodes in a matter of hours. Stainless steel and aluminum can be left bare without corrosion issues, as long as you keep the parts clean and out of the weather during storage.
  • To achieve a consistent brushed look on larger parts, finish it by hand with a hand pad, going in the same direction you were buffing in.
  • Always wear a dust mask or respirator and eye protection while buffing!

Not sure what wheel you need? Use the Wheel Guide

Pryme ships to any country in the world, please add your items to the shopping cart to see shipping rates.
U.S orders over $75 ship free!
Handling Time Orders ship out within 1 business day of receiving cleared payment. We do not ship on Sundays or holidays.
    International Buyers are responsible for any import duty or taxes. Sorry, we cannot mark the value of the package down or send it as a gift. Occasionally, packages may be held up in customs for a period of days or weeks.

      Tracking Information Tracking numbers will be uploaded to the order page and sent to your email inbox. It may take up to 24 hours for the tracking page to show the most recent information.

      We are not to be held responsible for stolen or lost packages, packages sent to the wrong address, or refunding/replacing packages in these scenarios. It is the customer's responsibility to file all shipping claims.

        Returns We accept returns within 14 days after your item has been delivered. If 14 days have gone by since your item was delivered, unfortunately we cannot offer you a refund. To initiate a return please send us an email at To be eligible for a return, your item must be in the same condition that you received it. The item must be unused / unworn and original tags attached. No returns allowed on sale/clearance items.

        Refunds Once your return is received and inspected, we will send you an email to notify you that we have received your returned item. Your refund will be processed and a credit will automatically be applied to your credit card or original method of payment, within 7 days. 

        Late or Missing Refunds If you haven’t received a refund for your return yet, first check your bank account. Then contact your credit card company, it may take some time before your refund is officially posted. If you’ve done all of this and you still have not received your refund yet, please contact us at

        Shipping Costs You will be responsible for paying the return shipping costs of your item. Additionally, the original shipping costs will not be refunded.

        Exchanges If you need to exchange an item, please see our refund policy above and include exchange instructions with the return. We do not offer exchanges on out of stock items. If the item is out of stock then we will refund you instead. The buyer is responsible for all shipping costs on exchanges.

        Incorrect or Defected Item If we made a mistake with your order, please contact us at We will provide a return label if an exchange needs to be made. You must notify us within 14 days of delivery of any defects with the item. Any claims past 14 days will be considered wear and tear, and cannot be replaced.

        Customer Reviews

        No reviews yet

        You may also like

        Customer Reviews

        No reviews yet